Sold out
OM606 / OM648 Crankshaft Dowel Pin Kit – Pulley & Timing Sprocket Reinforcement
Click to zoom in

OM606 / OM648 Crankshaft Dowel Pin Kit – Pulley & Timing Sprocket Reinforcement

BenzForce
BF697560622454
$79.00
Secure your Mercedes OM606 or OM648 crankshaft pulley and timing sprocket with the BenzForce Crankshaft Dowel...

OM606 / OM648 Crankshaft Dowel Pin Kit – Pulley & Timing Sprocket Reinforcement

Secure your Mercedes OM606 or OM648 crankshaft pulley and timing sprocket with the BenzForce Crankshaft Dowel Pin Kit.

Designed for performance engine builds, this kit provides additional mechanical engagement between the crankshaft and pulley assembly, reducing reliance on the factory Woodruff key alone.

Our precision-machined drilling fixture features an integrated 3/8-inch square drive, eliminating the protruding socket head found on some competing designs. This provides improved drill access and makes installation easier.

Key Features

  • Designed for Mercedes OM606 and OM648 engines
  • Reinforces the factory crankshaft pulley and timing sprocket connection
  • Precision-machined drilling fixture for accurate pin placement
  • Integrated 3/8-inch square drive for improved tool clearance
  • Alloy steel dowel pins for a secure interference fit
  • Suitable for performance builds and engine upgrades

Kit Includes

  • (1) BenzForce precision-machined crankshaft drilling fixture
  • (2) Alloy steel dowel pins — 5/16" diameter × 1-1/2" length

Required Tools (Not Included)

  • Size N drill bit:** 0.302" diameter, 4-3/8" overall length — McMaster-Carr #2901A157
  • 5/16" dowel pin reamer:** 0.3120" diameter, high-speed steel — McMaster-Carr #3002A28
  • 3/8" drive ratchet or suitable driver
  • Caliper or depth-measuring tool
  • Light hammer for pin installation

Installation Instructions

  1. Remove the crankshaft bolt. Leave the crankshaft pulley assembly installed and properly positioned.
  2. Install the drilling fixture. Thread the BenzForce fixture into the crankshaft and snug it securely. Factory crankshaft bolt torque is not required for the fixture. Tighten only enough to prevent movement during drilling.
  3. Drill the pilot hole. Using the specified size N drill bit (0.302"), drill through one of the fixture's guide holes. We recommend selecting a position opposite the factory Woodruff key.
  4. Verify drilling depth. Measure the drilled hole using a caliper or depth gauge. The hole must extend at least 1.5" from the pulley face. Drilling slightly deeper is recommended to provide adequate clearance for the dowel pin.  Important: Insufficient hole depth can make removal of the installed pin extremely difficult. Correcting this condition may require removing the timing cover and using a puller to remove the timing sprocket.
  5. Remove the drilling fixture. Carefully unthread and remove the fixture after drilling.
  6. Ream the hole. Use the specified 0.3120" reamer to finish the hole to its final diameter. Maintain proper alignment to ensure a consistent fit.
  7. Remove debris.  Blow air into the hole to remove any metal shavings
  8. Install the dowel pin. Carefully insert the supplied alloy steel pin. Light tapping may be necessary due to the interference fit. Avoid excessive hammering that could deform or mushroom the pin.

Important Installation Notes

  • Professional installation is recommended.
  • Confirm proper pulley alignment and drilling depth before installing the pin.
  • Prevent metal chips from entering the engine or timing components.
  • The dowel pin is an interference-fit component and may be difficult to remove after installation.
  • Follow factory specifications when reinstalling and tightening the crankshaft bolt.
  • This kit supplements the factory crankshaft connection; it does not replace proper crankshaft bolt clamping force.

**Application:** Mercedes-Benz OM606 and OM648 engines.

Read More
Read Less

Your cart

×


Notification Channels